Dodge Cummins Diesel Forum banner

1 - 20 of 22 Posts

·
Registered
Joined
·
707 Posts
Discussion Starter #1 (Edited)
We are going out to hot street performance tommorow starting at 10a.m

We are going to be dynoing a few trucks to prove dyno numbers wrong in buda.

All trucks are welcome to come 40 dollars for three pulls

No payout just a fun day to test the trucks

Minor tuning will be allowed


ok well my buddy is a idiot on the website haha!

Well we are heading to a guys shop at 8:30 workin on a couple trucks then heading to hotstreet at 10. We are going to be dyno'n as long as there is a truck to be on the rollers.
 

·
Registered
Joined
·
456 Posts
Looks like a porn site to me.
 

·
Registered
Joined
·
456 Posts
what city is this dyno gonna be at?
 

·
Valair Clutch
Joined
·
2,342 Posts
burleson tx its a top notch shop. ive dynoed there twice if we were closer i would be there for sure.
 

·
Registered
Joined
·
456 Posts
burleson?!

Dude im there!! give me a time and an address!!

Im only maybe half an hour out!!! And i will be on the Dyno.
 

·
Registered
Joined
·
456 Posts
that one works!

Ill see yall tomorrow.
 

·
Registered
Joined
·
707 Posts
Discussion Starter #9
Sounds good there wont be alot of us there but if ya get there and watch too there should be a truck that hits 1k.
 

·
Diesel Junkie
Joined
·
9,209 Posts
I would have been there but I didnt find out about it untill today!!! :doh: I'm on a rig just east of Mineral Wells
 

·
Registered
Joined
·
418 Posts
whats the deal with the numbers from buda
 

·
Registered
Joined
·
707 Posts
Discussion Starter #13
whats the deal with the numbers from buda
Well one of the guys in the Big Dawg had very low numbers for his setup and thought it couldnt be right as did everyone else. So we went to a dyno that we have been on before and was going to see if it was the truck or the dyno....well after blowing the turbo were not real sure :doh:
 

·
hydraulic lifter crew
Joined
·
12,297 Posts
could be that the dyno in buda was an
inertia dyno. is the other one you guys
ran on a load dyno ? if not your going to
get the sam crappy #'s.
 

·
Registered
Joined
·
707 Posts
Discussion Starter #15
could be that the dyno in buda was an
inertia dyno. is the other one you guys
ran on a load dyno ? if not your going to
get the sam crappy #'s.
Yes the dyno we went to was a load dyno and expecting better numbers but the turbo didnt like it to much haha!...we put a truck on the rollers that dyno'd at Buda and it was very close to the same numbers so we kinda ruled out the dyno being wrong.
 

·
Registered
Joined
·
12 Posts
Finally figured out my password so I figured I should post somewhere!

Had a blast at the dyno on sat!

Learned alot
 

·
Registered
Joined
·
1,135 Posts
Finally figured out my password so I figured I should post somewhere!

Had a blast at the dyno on sat!

Learned alot
any truth to the dyno #'s being wrong in buda?? I know we had a few buds lay down good numbers and the operators looked around like....:confused013:
 

·
Registered
Joined
·
12 Posts
numbers weren't wrong in buda.. THey were very close to the dyno we were on, I forgot what kind it was tho
 
1 - 20 of 22 Posts
Top