Search Results for ‘steering’

Hey everyone, I’ve had an issue after starting to work on my truck after the rollover. The power steering will only move a certain amount in one direction. About half of a steering wheel turn to the left, and 2 steering wheel turns to the right. I would like to get it figured out everything...

Hi folks, My truck has a popping sound when turning. I know there are hundreds of threads on this, and trust me, I've read every one. I've been using this forum for years as I've slowly upgraded my second gen, and I have always been able to find an existing thread that answered my question...

I was driving the other week and noticed that my steering was loose. Over the next few days, it got almost uncontrollable and would pull left or right every few seconds while driving. I have since replaced the steering box, all tie rods, drag link, and steering shaft. I have a video that I will...

Went lower and single few years back. Taking up space in my shed. Someone wants a dual setup.

I rebuilt the steering box in my truck the other day, put everything back in, confidently bled all air from the system, power steering would not work, with truck running or not, the steering was very stiff (even with pitman arm detached) pulled the box out again, I know the pump is working fine...

About 3 weeks ago now I got new wheels/tires and was checking clearance on them. As I was turning the wheel I lost my power steering. Went for a drive also noticed I had lost brakes as well. Tried bleeding the pump and that didn’t get me anywhere. So far I purchased and installed new power...

I'm not sure what year Ram switched the front steering configuration to where there are separate connection points on the passenger side steering knuckle for the drag link and tie-rod. This seems to be a superior design to that where the drag link connects to the tie-rod inboard of the knuckle...

Hey y’all. I’ve been fighting my truck 2013 ram 3500. Replaced all ball joints. Can’t keep the truck in a lane without running the center line. Wheel is hard to smoothly turn. I’m kinda thinking it’s the gearbox. I adjusted the gearbox little by little and problem only got worst any thoughts...

Hey All; I purchased a full EMF tie rod end setup with the plan to build my own, bulletproof front end steering setup. I used components from EMF and Synergy to complete the best setup possible. If you are interested in this setup then you know the EMF quality and engineering, there is not a...

Hey y’all, new to the Forum and diesels themselves. I’m a quadriplegic and just bought a 2018 2500 4x4 with 28k on it. I wasn’t able to test drive the truck before I bought it but had my dad do it so I had no idea how stiff the steering was compared to my 2011 Silverado 1500 4x4. I have a strong...

Anybody ever deal with a wobble in your first gen’s? My 93’ W350 has a wobble in the steering that starts right away and gets worse with speed. Most of my front end parts are old and tired; shocks, ball joints, wheel hubs, steering brackets, etc. I could do a full front end rebuild and likely...

So I installed a 4” skyjacker lift into the front of my dodge w250. I also installed the pitment arm (da20). The truck has 118.xxx km on it so it steered fairly well before the insulation, ever since the steering is so stiff you can’t even turn the wheel at a stand still. I ordered the DL10...

So I have a dodge off road tie rod and drag link with EMF rod ends...when i first installed them, it was what I thought was the best decision I ever made. As time went on I learned, thanks to Don Thurens hard work and research, that the factory mopar upgraded steering with a good stabilizer and...

I have a 1993 d250 that I bought recently and the whole steering wheel is messed up. I can't find a good tilt wheel for it anywhere close or for under $200. But 2nd gen ones are everywhere. I was wondering if it would plug up or better yet just be able to swap the entire column. Thanks!

I have been working on this issue for about 2 months now. Everything I have read and seen other people do I have done and it doesn’t seem to make any difference. truck is a 2012 with 150k miles. I have replaced all ball joints, wheel bearings, 3in leveling kit with shocks, redhead steering box...

I have a 1989 Dodge 350 2-wheel drive diesel dually that I salvaged from a farmer's field. I have an interference between the bottom front knuckle bolt and the lower arm as pictured. This truck has been rode hard and put away wet! I've got most everything else repaired except for this...

I just bought this truck and crawled around underneath to get a better layout of my new (to me) and first diesel truck to see entirely what the previous owner has upgraded. I noticed that the steering looks to have been upgraded to a newer gen model, but I don't know which one. Also, I noticed...

Hey all, I have a 2017 2500 with a level kit and 35’s on 20” rims. When I first bought the truck (it was stock but used) everything felt nice and tight and no play or any issues. Over the last few months however, the steering had been getting looser and there is a bad vibration felt through the...

Hi, This is the second time I am buying the inner tie rod for my first gen cumming tuck. First time from Oreilly store part and the second time from AMAZON by MOOG seller. I have ordered the same part number two time but for some reason, there are two little different items inside the box...

I put a 3 inch lift/leveling kit and 37” bfgoodrich ko2’s on my 97 2500 12 valve, the tires are obviously much heavier than stock so sometimes when I drive over an uneven bump or hole in the road the steering starts shaking and it feels like y trucks about to rattle itself to pieces, could this...