Search Results for ‘nv5600’

I've got a lot of questions so grab a beer. 1st off... this is a 2wd 2003 cummins dually with 485xxx miles and climbing quick. Bone stock. We haul horses all over. About 80k miles a year, usually around 10k pounds, with the occasional, once a month RV that is 15k. I have had nothing but issues...

My 05 Ram 2500 2wd is bone stock. I got an amazing 275K mile out of the original clutch. It started failing in October and I replaced it with a RhinoPac which included a new flywheel. I also replaced the fork, pivot ball, rebuilt and balanced the driveshaft. Replaced the hydraulics with a sealed...

This is a VERY POPULAR upgrade for G56, NV4500, NV5600, ZF manual transmissions! Fast Coolers add a significant amount of lubricant and aluminum surface area for heat to dissipate. Temperatures are reduced on an average of 30 degrees. The upper magnetic fill plug makes it easy to do a slight...

So boys fml clutch is ither smoked or soaked in oil and mail seal is dripping pretty good with any oil pressure. truck won move even in 4 low, wound out, I m wondering because of the fact I that I am going to be doing this solo would it be easier to pull the motor or push the 400lbs dry weight...

As the title states, I'm dealing with a low/no power above 2000RPM issue. I've got an 03 6 speed, original edge CS juice with attitude tuner, cts3 monitor, "cold air intake" with brand new filter. I originally thought this issue was fuel delivery as that is what it is 75% of the time. Replaced...

Hey there, starting on designing a project and want to know how much tourqe you could put through a NV 5600 or a G56 and be able to tow reliabley. The power plant is something that nobody's done before by combining two p pumped 24 valves together... I know it sounds nuts and everyone will think...

First time post here, but wow I've learned a lot over the years on this forum. This is a little write up on how I made a custom cooling loop for my 6 speed. This dropped my temp 15C, allowed me to install a magnefine filter, and gave me an easy way to add fluid and take samples for uoa. All...

Hello all, I am swapping an NV5600 into my '89 which currently has a Getrag but have some questions about the driveshaft. From what I've found the slip yoke for a 2wd NV5600 is a AAM 1485 U joint and there are no conversion joints available for that size. I found a 1485 weld on yoke for the...

I have an 01 24 valve HO manual that had the lift pump not turning on and it would run like ****, took forever to accelerate and sounded like it was missing turned out to be a broken wire and the ecm was not getting power so I believe the vp was making up for the lift pump not running. I have...

Looking for any tips for rebuilding a 2003 NV5600 (and then my buddy's 2002 NV5600).. I've got the socket for the mainshaft nut, I got a buddy with a good press for the gears On my tranny the rear mainshaft bearing went out, and it looks like the input shaft gear got a little warm (very slight...

Looking for help in a diagnoses before I pull the transmission, the other day I was driving my 04 3500 (11/03 manufacture) with a NV5600 in it and I just got this truck (sigh). I have had no transmission problems or any problems of any kind until now. I was starting to climb a small hill and my...

I'm looking into manual swap options once my 68RFE bites the dust. I'm leaning towards the NV5600 but need more clarification on a few items to be able to make a decision on the direction I want to go. Will the G56 Adapter Plate work for the NV5600? Will the 68RFE Tcase physically bolt to the...

Hello all! BLUF (Bottom line up front): I have an automatic 2005 Dodge Ram 3500 2WD that had it's automatic transmission swapped for an NV5600. The ECM is still an automatic... Therefore, it has 7 CEL codes that triggers "limp mode" characteristics (cannot rev past 2000 RPM in neutral or in...

I was thinking of purchasing these pto covers as a way for my temp sensor and to do fluid level without having to remove the shifter every time anyone used these or any experience with them?

Does anyone have a part break down list for a 48re swap to nv5600? The nv5600 is coming out of a 2001 24v H.O with manual t-case. as far as mine its got the 48re with 273 t-case. If anyone has a part break down with part numbers, where to buy if needed, schematic's etc it would be very helpful...

Hi! I live in Norway and have a 08 Ram 2500 6,7 with the rfe68 transmission. As far as I know this is the only 08 2500 in Norway, so it's a somewhat special car over here. I love the truck, but hate the rfe68 trans. So I am looking for all the parts I need to perform an auto to manual swap...

Start by disconnecting negative battery terminals, removing interior pieces and shifter, draining fluids, removing the driveshafts, supporting transmission with a good transmission jack (also always strap it to said jack using at least 2 ratchet straps), remove crossmember, unbolt transfer case...

Hi all, just reaching out to a forum to see if anybody’s got a smarter brain or has seen an issue that’s been plaguing my truck the last few months. Developed a knock that seems to run bad between 1400-1800 rpm regardless of gear, on an 04.5 with an nv5600 at 190000kms, automatically assumed...