Search Results for ‘injectors’

Who’s rebuilt their injectors with new shims and nozzles and how do you like it? My number 6 injector is slobbering. I can hear an injector knock and the exhaust port on #6 is a little wet. Praying it’s just diesel. Would nozzles and shims bring her back proper or would I be better off with a...

I've been doing allot of research and i think i might be able to do it myself i just don't know the right torque specs and do i have to get her tuned right after ? Injector replacement but i want to go over everything before i decide to dive in ,any tips? I only have hand tools no computer,i...

just installed new valve spring, headgasket , pushrods, head studs, and rocker arm bolts. I cracked the injector lines to the crossover tubes and have fuel coming out of them, I have 17psi so im not sure why I'm having a crank/no start. the injectors are all brand new as well. does this have...

Anyone know some good higher hp injectors for stock fuel and air system? my injectors have 290k miles on them and i’m gonna replace them with bigger ones but not trying to go huge but would like a little smoke and power. Any recommendations?

Just put a set of DFI SAC 7x0.013 injectors in the truck, would anybody be able to tell me the "hp" rating on these? i've looked at other threads on here and haven't really found a solid answer.

Not sure where to start so - I have 30% over injectors, less than 50k miles old from Exergy (truck 280k) tuned with a RaceMe Ultra on +60hp tow tune. During the summer months, if I ever did a hard pull I would get a CEL with code: P0087: Fuel Rail Pressure Too Low. Back then I would think...

hey guys this post is for a 2005 5.9 L Cummins common rail w/ 400,000 KM. so I've recently just come across an issue with my truck where it has a really bad vibration and a knock coming from my motor. along with that, it was puking white smoke at the time. without much hesitation I ordered...

I have been fighting the wts light when towing and I have replaced about everything. Capped the rail, FCA, CP3 Gear, High pressure fitting, cascade crossover valve, fass 165. I recently did head studs and I found a set of reman injectors with 30k miles on them. My WTS light rarely ever comes in...

Just bought a 1991 D-250, needs a trans cooler and lines. Where do I find the parts, and also what injectors would you suggest.

Ive had my truck a little over two years now and I've always wanted to make it around 400hp to the wheels. I hardly ever tow anything and if I do its a ~5000lb boat/trailer. I do about a 50/50 ratio of city and freeway driving. I want to make more power because I use my truck to drive down to...

Hello, Looking for recommendations on replacing injectors. I have a stock 2004.5 5.9l 2500. It has 199K with no issues. I added a 2 micron CAT fuel filter a couple months ago and just installed the Banks intercooler with monster ram intake system. I plan on taking a cross country trip in a...

Alright, I think its time to put Injectors in my truck. I'm just having trouble deciding exactly what I want to do, so would love to hear some opinions! To start, the truck is a 2005 Ram 2500 5.9. It has 240000 KM's on it (about 150k miles). Injectors have never been done before. Trans is...

Hey guys I’m lost here I have a 06 6spd Completely stock I just put all 6 brand new injectors ( GP Sorensen ) , New Bosch Cp3 ( New not rebuilt ), Sinister diesel cat fuel filter adaptor, New lift pump ( stock ) Properly adjusted all of the valves, Made sure each injector is getting power...

Recently I posted a thread about how my truck exhaust would make a chugging noise at idle, but recently I’ve noticed it’s running very hazy especially when it’s cold, this morning was about 65 degrees outside and it blew whiteish grey smoke at startup and ran very hazy for the first pull up the...

Hello Everyone, new to the form. I'm trying to size the right injectors for my truck. Its a 01 24v, with compounds on it (62/71/.07 over a S480). I did head studs, o-ringed the head, and high rev valve springs when I put the compounds on it. I'm running a ZF6 and 3.73s. Right now I'm running...

2013 Ram 3500 6.7 Engine rattles like the timing is severely advanced. It lopes at idle, try’s to push through the brake when stopped in gear due to the lope, and surges at cruise. I am at a total loss. Very touchy throttle when you first take off. To make matters worse, it usually doesn’t act...

I have a 99 automatic I put a new head and studs on it and 75hp injector but it will only run on 1 and 6 cylinders. So far I have put a new fass 165 New vp44 and New cummins cross over tubes and I have but a break out box on it as well but through everything still only 1 and 6 are running is it...

I am thinking about getting the POD injectors (50hp) for my non-ic 1991 12 valve. I am also turning up maximum fuel screw and advancing timing. I thought i could still get by with just a cold air intake and a 4" downpipe while still having an OK fuel mileage. But I was looking around today and...

I just finished installing a set of BBI stage 1 injectors. Flashed a tune and started the truck up and it sounded really bad. Pulled the valve cover and all the rockers are seated in the push rods and on the crossovers. I linked a video if it running below. I'm not sure what to do next.

This truck has got me stumped, I’m having a few issues and would appreciate any insight! So if I start the truck and drive it when the engine temp is below 100 degrees( pretty much when I get in and go) I will get a big puff of white smoke only if I get on the throttle hard( like floor it) it...