Dodge Cummins Diesel Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 29 Results
  1. 89-93 Powertrain
    I had my injectors tested last week and they were between 50-450 PSI below pop level, so I had them replaced with brand new Bosch (stock) injectors. I installed them and torqued them to 50lbs. None of them are leaking and I have fuel all the way up to the injectors, but I’m still not getting any...
  2. 98.5-02 Performance Parts Discussion
    I'm wanting to buy some injectors and been looking at 150hp ones, I have an edge HT tuner and engine is completely stock. would I be able to run the injectors before I get a bigger turbo? Or would the egts be too high? Since I have stock turbo about how much HP would it give for now if I get...
  3. 3rd Gen. Non-Powertrain
    2 days ago, I took off my muffler on my 2006 2500 with the common rail 24v, just this evening it threw a check engine light and starting running absolutely terribly, codes pulled were P0606 - internal control processor AKA the death code, P2146 - fuel injector group 1 supply voltage...
  4. 3rd Gen. Non-Powertrain
    My 2006 2500 was sitting for a bit while the transmission was being built and replaced. I also put a brand new lift pump on it and it started and ran just fine. I took it for a drive and then it seemed like it started to miss. I attached a code reader and got a P0306 cylinder misfire code. I...
  5. 3rd Gen. Powertrain
    Hey there, first post so please ignore my ignorance. https://youtube.com/shorts/FP8QO1gTjQQ?feature=share 2004 ram 2500 5.9 common rail Has about 240K miles on it. Dash is getting old, the odo stopped working. Front main seal leak, just did an oil and fuel filter change. Knock was there...
  6. 3rd Gen. Powertrain
    Hey, all I was driving the other day and started hearing a weird ill call it whirring noise that got progressively louder then evolved into the extremely loud knock that you can hear in the video I linked. I thought it was injectors so i pulled them and had them tested and they came back all...
  7. 89-93 Performance Parts Discussion
    Looking at doing a sxe362 and was wondering what size injectors you would recommend, was think 6x13s but I am pretty new to this. current mods are fuel pin, 3200 governor spring, 1/8 timing bump, he351cw, raptor lift pump, fuel screw maxed, g56 with 600hp valair clutch, turbo back 4 inch. This...
  8. 3rd Gen. Performance Parts Discussion
    Debating between 150% and 200% injectors on a 06 5.9, have a 12mm cp3 and compounds of a stealth 64 and s488. Trucks mostly a weekend street truck. How are the street manners of 200% overs? Able to keep the smoke down when just driving around? Would like to be able to make 1000whp with some room...
  9. 89-93 Powertrain
    I know this question has been asked a million times on this site but I couldn't find a good answer for the non ic trucks. If I can remember right they start out with about 40hp bigger injectors than the ic trucks. If this is true and I wanted a 50hp-70hp bigger injector, and since everything is...
  10. DDP Motorsports
    Fleece just released their new 6.7 Cummins injector lines. These are excellent replacements for damaged/leaking lines or if you just want to replace them as part of your preventive maintenance. Feel free to message, call or email us if you have any questions...
  11. 2010-2012 Powertrain
    UPDATE AT END: Hey y’all, quick question. Recently put some new tunes on my truck (after a 2g swap) and it’s acting different now (obviously duh). But it runs/drives a lot smoother, however, when the engine is cold at idle and when at low rpm driving the engine is much louder than prior to the...
  12. 3rd Gen. Powertrain
    Recently I posted a thread about how my truck exhaust would make a chugging noise at idle, but recently I’ve noticed it’s running very hazy especially when it’s cold, this morning was about 65 degrees outside and it blew whiteish grey smoke at startup and ran very hazy for the first pull up the...
  13. 98.5-02 24V P-Pump Conversion
    Searched and searched to no luck. Im trying to figure out what ppump setup i can put on my 24v that can support 500-700 horse and be used as a street/strip/tow/daily. Can a 165 pump support it and with what mods to the pump? I know a 215 pump would support it with mods, but need those specs...
  14. 3rd Gen. Powertrain
    Need help with a potential issue. Truck is a 2005 5.9L 325/610 4x4 auto w/265,400 miles. All stock except for FASS system and gauges. I run a bottle of Stanadyne every fill up. Oil used is Schaeffer’s 5W-40 OTR Plus CK-4. I have been noticing (from my mirror) light black smoke under easy to...
  15. 3rd Gen. Non-Powertrain
    Not too long ago I had this plague of a code on my 03. I found and fixed the problem and saw several posts about different problems so thought I'd share mine. The CEL would light up and truck would go into limp mode shutting down the rear bank. Forcing me to run on 3 cylinders. It was...
  16. 07.5-09 3rd Gen 6.7L Performance Parts Discussion
    Will a S475 over a S366 be enough air to support 125hp injectors and dual cp3. Also will it tank gas mileage if so what injector can I keep economy but also make around 800-900 hp with.
  17. 98.5-02 Powertrain
    Replaced my injectors with stage 5 DDP's (that someone had sitting on there shelf never used is what they said) because i was having a misfire/surging going on since i changed them it'll fire up no problem but im having backfire/pop sound. So i cracked each injector line at the head 1-4 all...
  18. 3rd Gen. Powertrain
    So I dont know too much about injectors and such but I have been on a few threads here. Truck has 184k with stock everything, the injectors used to idle roughly and shook the whole truck badly at idle and it almost shut the trucj off when it was fully warmed up last summer. Doesnt happen...
  19. 07.5 - 09 3rd Gen 6.7L Powertrain
    Getting a very loud rattle and loss of power if I accelerate hard, normally happens between 1500-2000 rpm, gets worse if I turn up the fuel or timing with my juice with attitude, I’ve replaced the fuel pump/ fuel filter/ fca/ and put in a rail plug, still no change. The truck will blow black...
  20. 3rd Gen. Performance Parts Discussion
    Hey all, new to the forum... I am beginning to build my 05 cr cummins, and as I order performance parts I could use some advice narrowing down exact parts. My goal is a reliable DD, used for occasional towing(3000-10000lbs), and obviously once its built some horseplay from time to time. HP...
1-20 of 29 Results
Top