Search Results for ‘injection pump’

(posting for a friend) No start, cranked, primed, bled, no start. The first thing he noticed is the p pump or ofv does not make a sound while priming?? You know that air hissing sound you get after pushing the plunger 20 or so times nada He is getting fuel out of the filter housing bleed...

I have a 20 Ram 2500 mega longhorn Cummins (zero mods) with 59k miles that has been at the dealership for 16 weeks and counting. I have been servicing the truck every 10k miles. At 50k miles, I changed the oil and fuel filters and noticed after the service that the truck was running rough at low...

This is a saga about a 2002 RAM 2500 Cummins. In September, on a drive from CO to TX, it started acting weird. Bucking a bit and losing power. I thought it was an electrical problem. Then I thought it was the fuel filter, so I replaced that. Then I thought it might be the head gasket and...

I just bought a 91 12v non Intercooled has a new Bosch ve pump on it it starts right up but has a rough idle and blows white smoke any ideas what it could be?

So I have a 1999 24v 3500 dually 2wd, Standard, lately when I try to accelerate the truck will spit and sputter like it’s not getting fuel, it would run great till it got warmed up and then it would start to do it but this morning I went to go to the parts store and it fired up fine but as I...

I am officially stumped with my truck. It’s a 97 12 valve p pumped with 191 delivery valves also has a fass lift pump on the frame rail. I noticed a knock the other day so I tried to see where it was coming from and sounds like the passenger side of the motor but what boggles my mind is that the...

Not sure where to start so - I have 30% over injectors, less than 50k miles old from Exergy (truck 280k) tuned with a RaceMe Ultra on +60hp tow tune. During the summer months, if I ever did a hard pull I would get a CEL with code: P0087: Fuel Rail Pressure Too Low. Back then I would think...

Hi guys, I got a 2000 Ram 5.9 Cummins 5 speed. When starting it in the morning it runs great for about 5 minutes then she starts to run rough. Idles between 800rpm to 1000rpm up and down. I noticed it does it also when the grid heater comes on and lights will dim and volts go up and down. Also...

I am currently building a mild ISB 235 for a hot rod project with a 6psd 2wd manual I have an agricultural QSB motor for some parts, it has and electronic injection pump set up on a 12v, PV30. wonder if I can make it work on the 24v motor. ? Seems like it should all bolt up and set up fine...

Hey guys just curious to who has fixed a leak on the p pump mounting bracket where the two torqs bolts go into the block behind the steering/vacume pump. On my first attempt at fixing the bad leak I pulled the steering/vac pump, rebuilt the pump, removed bracket fastened with two torqs bolts...

Have a 93 d250 was thinking about putting a P pump in my truck. Just wondering Pros/Cons or if I even need to worry about it. Have an HE351 turbo to put in it and some injectors. Would it compliment those? Thanks in advance.

I have a 2004 5.9 with 345,000 on it. When motor is not being stressed it will occasionally hesitate and the check engine light comes on. Code is for low fuel rail pressure. After the hesitation the truck performs normally and the light (check engine) goes off after a day. Fuel filter is new...

I recently purchased a '94 12V with about 200k miles- it ran great up until last week. I went to start it and it had a rough idle, drove it down the street and it was puking white smoke, popping and had no power. Got it back and realized a copper line (that i think goes to the fuel pressure...