Dodge Cummins Diesel Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 28 Results
  1. 07.5 - 09 3rd Gen 6.7 Liter General Discussion
    Hey all, wondering if any of you can figure out the ignition problem I am having. There are 2 scenarios that happen occasionally and I believe the are related: 1. When I cycle the key to the 'on' position, the dash/gauges do not light up right away... there is up to a 5 second delay before the...
  2. 2010-2012 Powertrain
    Hey all, have this thread in 3rd gen, but since g56 is also 4th thought i might get some more help here also. Been digging and reading about the heavily debated g56 preferred oil type. Also not a fan of ATF so i have come up with a few others that seem to be my best options. I will put ATF up...
  3. 07.5 - 09 3rd Gen 6.7L Powertrain
    Been digging and reading about the heavily debated g56 preferred oil type. Also not a fan of ATF so i have come up with a few others that seem to be my best options. I will put ATF up for those who think it is good option. My truck is an 09, tuned, and i believe it has a dual disk from...
  4. 07.5 - 09 3rd Gen 6.7L Powertrain
    Ok, so I have a 2008 dodge ram 2500 set 6.7 and got rid of the 68rfe and put in the g56. I about have everything squared away, even wired the nuetral safety wire to ground, only the truck wont start. I haven't flashed the ecm yet because I figured I could drive it to the dealer to have them do...
  5. 07.5 - 09 3rd Gen 6.7L Powertrain
    i have a 2008 6.7 g56 when the trucks started there is no noise after driving for a bit and letting it get up to temp once sitting at a stop it’ll make a noisy chatter like gravel rolling around in the trans case when you push the clutch in it goes away and shifts fine, sometimes while it does...
  6. 3rd Gen. Powertrain
    Pretty much finished my last step of the swap today. The tuning. For me I bought a Smarty Jr. then contacted Smarty and they had a auto to manual recover written for it. I downloaded SmartyUDC, then they email me the file, I plug the Smarty into the computer via a simple printer cable that’s $6...
  7. 2010-2012 Powertrain
    I was having issues shifting my 2012 ram 2500 G56 into first and second gear at a stop. First thing to check is for any issues under the dash like anything bent or broken or worn out causing excess slop in the clutch pedal travel. Next check for low clutch fluid (if its a solid flywheel...
  8. 2010-2012 Powertrain
    2012 3500 6.7 g56 has southbend dd clutch locked out of 5&6 every other gear works fine including reverse will go in fine and shifts fine but once I take it out of 4th it won’t move over to go to 5th or even down to 6th just bought the truck 2 weeks hoping someone can please help Any help is...
  9. 2010-2012 Powertrain
    I'm just try to see what brand would make a good replacement clutch for high traffic areas. I have a 2011 2500 4WD with the G56, just hit 132000 miles and the stock clutch started rattling and slipping a bit so I know it's time to replace the clutch, I just want to know if I should do a stock...
  10. 2010-2012 Powertrain
    I towed my camper home this morning and backed it into its spot without issue. Slight smell of burnt clutch but my unusual as my camper parking spot is a tough one to get into. Went to pull out and I as I pushed the clutch pedal I could feel and hear the clutch fork hitting the pressure plate or...
  11. 2010-2012 Powertrain
    Finally lost 4th gear on the g56 and can’t find much info on who sells a good built (cryoed gears,better case) for the g56 I’ve looked at the cpp diesels extreme g56 and lazersmiths gorilla56 and seen mixed reviews on those company’s I tow 10,000 plus often and the truck is full second...
  12. 07.5 - 09 3rd Gen 6.7L Powertrain
    Hi all. New to the group, and I see lots of posts and threads, but figured I would post what I am up to. I tow a fifth wheel, about 15k, and use as daily driver when not driving the Prius. Have started reading, and following all the info already posted, but appreciate any pointers. Plan on...
  13. 3rd Gen. Powertrain
    I just completed installing a new South Bend Clutch on my 2006 4x4. While I had the transmission out I split the G56 case apart so I could take the bell housing to a welder to reattach a piece of the housing that had broken off. The welder did an excellent job and I re-assembled case...
  14. 3rd Gen. Powertrain
    Hey all. I have owned my truck for about 30k miles. I am going to start with my clutch. I have no maintenance history before 178k miles. Judging from some aspects I have repaired, this baby was run hard and put up wet. But back to the topic. I have the following: Fleece Cheetah ATS...
  15. 2010-2012 Non-Powertrain
    I was thinking of purchasing these pto covers as a way for my temp sensor and to do fluid level without having to remove the shifter every time anyone used these or any experience with them?
  16. 07.5 - 09 3rd Gen 6.7L Powertrain
    Truck will not start. Was running perfectly fine. Until the other day I went to go leave work and no crank, no click either. Turned the key on and had power (Headlights lights, radio, dash display, ect) . Amperage Gauge was reading properly. But when I went to start the truck nothing... had to...
  17. 07.5 - 09 3rd Gen 6.7L Powertrain
    Hi! I live in Norway and have a 08 Ram 2500 6,7 with the rfe68 transmission. As far as I know this is the only 08 2500 in Norway, so it's a somewhat special car over here. I love the truck, but hate the rfe68 trans. So I am looking for all the parts I need to perform an auto to manual swap...
  18. 3rd Gen. Powertrain
    Start by disconnecting negative battery terminals, removing interior pieces and shifter, draining fluids, removing the driveshafts, supporting transmission with a good transmission jack (also always strap it to said jack using at least 2 ratchet straps), remove crossmember, unbolt transfer case...
  19. 98.5-02 Powertrain
    So i recently picked up a g56 from an 08 ram 2500 with the 6.7. I got everything from the adapter plate on the back of the block to the transfer case, what I am looking to do is replace my nv4500 on my 5.9 12valve with the g56. Any help would be appreciated and I also have some questions. -...
  20. 3rd Gen. Powertrain
    Ah yes, I decided to attempt to kill 2 birds with one stone! Asking two questions out of curiosity: 1) My G56 I am currently rebuilding had the 4th gear synchro COMPLETELY burnt and seized up. It was so bad it just would not even go into 4th gear at all. Luckily no gear or bearing damage, just...
1-20 of 28 Results
Top