Dodge Cummins Diesel Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-12 of 12 Results
  1. 3rd Gen. Powertrain
    I recently purchased my grandfathers 2004.5 Cummins 4dr long bed and have been doing the much needed maintenance after 242,000 miles. Needless to say it didn’t always get maintained and I just replaced the stock injectors and started to service the trans. That’s when I found about 4 inches of a...
  2. 3rd Gen. Powertrain
    I just recently completed a g56 swap from a 48re, now when I try to start it it won’t even crank. I have the three pin neutral saftey plug with a yellow with blue tracer, a solid yellow and green with yellow tracer wire, if I tied the yellow together and ground the green truck starts but once...
  3. 98.5-02 Powertrain
    Hey ladies and gents, I’m new here. I’ve visited this page a lot for answers but I can’t find jack about one thing. I have a 01 2500 5 speed… it’s geared like a tractor, I’m starting to notice the clutches are getting wore, and instead of tearing into this trans, I would like to swap it. What...
  4. 07.5-09 3rd Gen 6.7L Performance Parts Discussion
    I am swapping the G56 into my 2008 2500 6.7 that originally had the 68RFE. The truck has an Industrial crate engine with full emissions delete, and has compound turbos and looks to have had an EFI Live tuner. The truck has an OBD jack on it that leads up to a 5-way switch on the steering...
  5. 03 - 07 3rd Gen 5.9 Liter General Discussion
    Hey guys my tranny is going out on my truck and want to convert it just for the fun of it. Don’t want to argue about why. I know there are posts all over on this topic but it’s hard to find more specific details for my truck. I have a 2003 quad cab 4x4 short bed. I don’t have any parts yet but...
  6. 98.5-02 Performance Parts Discussion
    I'm sure this horse has been beat to death just wanted to see what actual people that have done this swap think and how it handles power and what it's reliability like my rigs a work truck gunna get 100 sticks and prolly a s300 eventually or do turbo lab Americas 62 hybrid not trying for power...
  7. 3rd Gen. Powertrain
    So I’ve read the very detailed post from MTBMike probably 3 dozen times end to end. I’m in the middle of my swap with everything installed, and im trying to figure out this clutch safety switch to get it to fire, as right now it won’t. I have the Yellow with with blue trace grounded 100% and the...
  8. 2013-2018 Non-Powertrain
    Finished up my swap on Saturday and grounded out pin 4 on my trans connector like I had read in other forums to get it to start. Truck started and ran fine had check engine lights of course considering the truck still thought it was an automatic. Finally got my manual tunes from ez Lynk drove it...
  9. 07.5 - 09 3rd Gen 6.7L Powertrain
    So i recently picked up a g56 from an 08 ram 2500 with the 6.7. I got everything from the adapter plate on the back of the block to the transfer case, what I am looking to do is replace my nv4500 on my 5.9 12valve with the g56. Any help would be appreciated and I also have some questions. -...
  10. 3rd Gen. Powertrain
    Yes i've googled, and searched everywhere and can't seem to find anybody that has experienced this issue. Just did the G56 swap on my 2006 Dodge Ram 2500 Mega Cab 5.9, everything was swapped correctly without any issues. Wired up the clutch safety switch properly because when I try and turn the...
  11. 3rd Gen. Powertrain
    Long shot but im looking to swap my 2006 48re to a manual. Either g56 or nv5600. So if your interested in trading setups let me know. Im located in hendersonville north Carolina 28792. Trans has upgraded transducer and gov. And I have a bd diesel pressure enhancer. Truck is daily driven. Can...
  12. 07.5 - 09 3rd Gen 6.7L Non-Powertrain
    I bought a pre filled mastercylinder but did not come with bracket to mount through fire wall does anyone know where i can find the peice that smaps to it thats all i like.
1-12 of 12 Results
Top