Search Results for ‘ecm’

Hey guys, I’ve been battling an issue with my 98.5 24v 4x4 first start up it high revs up to about 2000-2500rpms only in park and neutral, in drive it idles around 1200-1500 and I have no throttle response, if the trucks been sitting awhile every now and then it won’t do this, however, it...

So I have a 2011 Ram 2500 mega cab. I had some wiring issues that have since been fixed but the computer was damaged in the process. I have one that is the same part number so I installed it and it fixed my issue. The only problem now is I need it synced with the truck. I did change the vin with...

I have an intermittent cranking issue. It will crank for 2-3 seconds then stop and almost sounds as if the engine tries to rotate in the opposite direction when it stops then it repeats this process. I reinstalled all my injectors today. I pulled them out to do a visual inspection mainly of the...

New member, been searching for answers and haven’t found anything. Hoping someone here might have dealt with this or have some insight. Truck is an 08 Ram 2500 6.7 G56 Deleted/ Tuned with HS minimaxx Truck was having issues with the electric 4wd shift. It was getting stuck in 4wd and then...

What all does the ECM need to see in order to start/run? I assume it needs to still communicate with the TIPM? I have a 2008 Cummins, but has no crank/no start, and the fuel pump relay keeps cycling on and off... Shop replaced the ECM, but it still won't start, and they jumped the starter and...

Okay, so I was driving down the highway and out of nowhere I lost power to the trans and the engine was spitting and sputtering, from there on I got it to the side of the road and it died I got it start one more time it ran horribly and still had no trans. Now at home all it does is just crank...

2008 Dodge Ram 2500 6.7L. I did the g56 swap, and ended up recklessly grounding the wrong wire for the park/neutral. I ended up grounding the white with blue tracer, since the white looked like yellow due to the age of the truck. It of course did not work, and ever since then the truck won't...

Codes: P0251, P000F, and P0087 This will be kinda long to explain whats happened but im going to give yall the best details i can. Working with an 07 3500 6.7. (History) it is deleted and tuned (H&S mini maxx) also has rapture 4g lift pump. ran stock fuel canister for a while it always leaked a...

1991.5 D250, 5 speed getrag, with ECM Removed/Deleted items: • External Voltage Reg (wired in a self exciting internal voltage reg per benhillman walkthrough) • CPS (was there but hooked up to nothing) • A/C (leaked, compressor seized, condenser coil leaked) • Cruise Control (was missing...

I've read about tuners and gauge clusters and all the various add-on's that are out there but it seems that the ECM has all the readings that the add-on's are attempting to deliver. Wiring or plumbing to individual components seems to me to be duplicating what the ECM already knows. Is there...

I have a 1999 dodge 2500 2wd automatic that has 95k miles. The truck will start up just fine and crank just fine and idle just fine but won’t go over 10 mph or rev over 1400 rpm. I’ve been looking for a solid week for help or someone with the same issue that actually has a resolution to the...

Recently bought the truck, spun #6 bearing. Rebuilt engine new crank, rods and bearing. Went through the warm up/ coolant purge cycle little smoke cleared up nice smooth idle. Now I have developed P0606 that will come up after running for a few minutes with a rough idle, not a full misfire but a...

Hey guys, I recently purchased an 01 5.9 Cummins from a farmer. Had been sitting for a year because he never had time to put the nv5600 in it he had. Current transmission is missing reverse and 5th. Anyway I had a p0237 code and no turbo power. Replaced the map sensor past night and ran...

Hi everyone this is my very first post. I have a 2000 dodge 5.9 Cummins 5 speed. I'm having issues with the map sensor. I get codes p0237 p0236 Low cricut so, I bought a Cummins map sensor that didn't fix it. I followed moparman's post about disconnecting map sensor and Ecm to see if there is...

I have a 2002 Dodge Cummins 6 Speed Manual. I've had recent issues with the truck dying/bucking (WTS light flashing when happening). Seems to get a lot worse when I load a tune into the truck. This morning on my way to work, the truck proceeded to do the same thing on me, died and then threw me...

All, As you can tell by my title of my post, I’m having a rough bit of luck with my truck. Two months ago, my truck, a 2011 Ram 3500) unexpectedly quit after driving a 3 hour trip. Truck ran fine until I parked it for the night. Went outside the next morning to start it and nothing happened...

Howdy all, was at a big car show today, and did a big burnout, at the end of the burnout, the truck shut off, wouldn’t start. It got hot but not out of the comfort zone. I’m having ecm problems (wts light refuses to come on anymore and weird starting) I put some fuel in the truck, bled the...

Help please my positive battery terminal rattled loose came off the truck died while driving I reconnected it and now the truck cranks but wont start it's bone stock I put brand new batteries in. When I turn the key to the on position the fuel pump does not appear to run I watched it with the...

First time posting. 2001 Dodge Ram 3500 slt Laramie 4x4. So, I have been having this problem for the past couple of years. Truck runs strong for 2 or 3 days and then I get the dead pedal. You can readjust the battery cables and and retighten and it will normally go 2 or 3 days without any issue...

I have a 2001 6 speed manual 2500 with a dead pedal/runaway throttle, it changes randomly and sometimes will almost redline without me touching the pedal. It will drive normal for a few minutes then start doing this every time. At first I thought it was the TPS but I have put 2 different ones in...