Search Results for ‘cp3’

I have a 2005 dodge ram 2500 with 163k on it and it drives fine and doesn’t seem to be down on power but on decel it skips almost, I put 6 new injectors in it thinking the issues was leaking injectors, that was not the case I did a cylinder cutout test for each cylinder to try and narrow down...

I have an 05 3500, 6 spd that's been broke down for 2 year and been to 5 shops and no one can figure out the issue. Let me preface by listing parts and work done. 2 new CP3s from Bosch, injectors 4x also Bosch, connector tubes, multiple FCAs, ECM, new rail, lines fuel pressure sensor and valve...

Deleted 2009 truck Stock with a hot tune 35psi runner Recent fuel problems after no recent mods. 126k on the clock Rev max 700 lift n 35s Dialable hp switch Unplugged sensor at cp3 fuel goes to 21psi plug in back to 5 psi after say 15 sec. Put in a cam sensor because have gotten this code...

I installed a fleece in tank lift pump a few thousand miles ago and a new alternator closer to a thousand miles ago. Starting about a week ago my 2004 with an in tank pump died while pulling out of my driveway and threw a WIF light. I’ve put a new filter on it, put diesel dry in it, done...

This is for a 2006 5.9 Picked up a used ppe dual kit off a buddy, debating on selling it for some cash to put towards a 12mm stroker or trying my luck with it. Which option would be better for 1000+ whp? Build is slow going and working on accumulating parts to all be installed at once. But plan...

I got some bad fuel in my 07 5.9l so we dropped tank and cleaned it completely out, put new filter in, replaced, cp3, and the fuel pressure release valve. Truck was running perfectly fine before the bd fuel. But now won’t start and makes a sucking sound when trying to start. It also is now...

I have a 2015 ram 3500 Laramie bone stock 150000kms(90000miles). I have linked a video with a tick/knock I can hear at idle. Should I be concerned with this or is this just CP3 knock.

I am looking for some help diagnosing a hard start on a recently purchased 2003 5.9 CR Cummins, I have searched a lot on this forum and done a tonne of reading. Truck is higher mileage at 470,000 km. Sometimes the truck will start on the fifth rotation sometimes it will take turning it over for...

I'm needing a new cp3 pump for my 06. Im seeing many different rebuilders... Im just looking for stock rebuild. Thoroubred $565 2 year warranty up to $815 DDP 1 year warranty. Any suggestions to avoid would be greatly appreciated.

Just replaced top cp3 from ATS twin fueler kit since old one decided to shred itself. Put new cp3 in and hooked up all correct lines and plugs for FCA/FR-PS. Primed system 4 times and cranked it over. Started up really rough with a giant chop. Eventually turned itself off after chopping for a...

So my head gasket blew about 2 months ago. So I put a new one in did the head studs with it. All is good no over heating or any signs of not doing it correct. But here’s where my issues start. At first I had a slight boost leak no big deal bought a new 30 dollar gasket, took the injector lines...

Hope someone has some insight... loosing my mind lol. Let me start with my truck and how this all started I have an 03 3500 srw 246,000 miles Things I've done over the last 8 years Fass 150 Platinum (single filter)(6yrs ago) Aftermarket wastegate (6yrs ago) Smarty SP06 POD (7yrs ago) Fully...

I hear people talking about using engine oil on the seal on the cp3 before installing. Would white lithium grease or break cleaner work? Just wondering

So I’m installing a Industrial Injection Bag Of Parts and removed the pump gears and the shaft seal with the red metal backing is stuck on the CP3 still and I tried to grab it with needle nose and Narled it up some so don’t want to just leave it and pull the new one off the new gear box but she...

Hi all-- Recently inherited a 2011 6.7 from my father. It has around 105,000 miles on it. Long story short: Pops didn't change the fuel filter enough. He took excellent care of the truck regardless but the initial filter wasn't changed until way too late. Truck threw a fuel rail sensor. I...

So I recently figured out that my air dog hasn’t even been plugged in for who knows how long. I’m running duel cp3s and they have been buzzing when I turn the key to let it warm up. Curious as to how bad it is for the cp3s to basically act as a lift pump?

I have a 2007.5 6.7 it starts and idles at 7000 psi but will not build past 13000 psi. I am in the process of changing the injectors. I replaced the fca and the rail pressure sensor but nothing changed when I unplugged the fca the cp3 did not changed the fuel pressure at all same way when I...

Hello y'all new here to the forum and first time posting as well. I'm hoping somebody can help me with my situation or can give me a little insight. I have an 04.5 Dodge Ram 3500 6 speed with no start situation. At first, of course, when working would fire right up with no hesitation then within...