Dodge Cummins Diesel Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-18 of 19 Results
  1. 98.5-02 Powertrain
    I have a 99 5 speed 3500 Cummins, I’ve just replaced the clutch for the truck and now it will not go into gear, the truck try’s to move forward when trying to put it in gear, I think it is the clutch pedal and slave cylinder but I’m not completely sure.
  2. 07.5 - 09 3rd Gen 6.7L Powertrain
    i have a 2008 6.7 g56 when the trucks started there is no noise after driving for a bit and letting it get up to temp once sitting at a stop it’ll make a noisy chatter like gravel rolling around in the trans case when you push the clutch in it goes away and shifts fine, sometimes while it does...
  3. 3rd Gen. Powertrain
    Wondering if yall might know what this sound is coming from my clutch/transmission... it first started you could only hear it in 3rd gear, it's a kind of growling spinning noise. We were coming home to Texas from Nebraska with a load of cows. By the time we got home, you could hear it in 2nd and...
  4. 3rd Gen. Powertrain
    Hello, I've got an 04 ram with the nv5600 and I'm i’m looking to get a new clutch for it, I know that the South Bend and the valair clutch are Basically best ones but I’m not looking to spend that money right now and I was wondering if anyone has had a ClutchMax Clutch and how's it handled up?
  5. 98.5-02 Powertrain
    I went through a mud hole and after that my clutch pedal was sticky. Not to an extent it’s not drivable but I would like to figure out what it is. It only does it when the truck is on. Any ideas?
  6. 2010-2012 Powertrain
    I towed my camper home this morning and backed it into its spot without issue. Slight smell of burnt clutch but my unusual as my camper parking spot is a tough one to get into. Went to pull out and I as I pushed the clutch pedal I could feel and hear the clutch fork hitting the pressure plate or...
  7. 98.5-02 Powertrain
    I have a 6 speed 02 ram 3500 that the clutch recently went out on, so I had a new 1 put in. The person doing it for me of course dropped the light bulb in his head and got air in the system. Even after bleeding it, putting new clutch master cylinder in and bleeding, him dropping tranny again...
  8. 07.5 - 09 3rd Gen 6.7L Powertrain
    Hi all. New to the group, and I see lots of posts and threads, but figured I would post what I am up to. I tow a fifth wheel, about 15k, and use as daily driver when not driving the Prius. Have started reading, and following all the info already posted, but appreciate any pointers. Plan on...
  9. 98.5-02 Powertrain
    About to put in a SBC single disc 13125. I have a new fly wheel, clutch, hydros, throwout bearing, clutch fork, pivot ball. I have also just replaced the rear main seal as I was taking out the old clutch. Before I installed a new clutch, can anyone give any insight on what happened to my old...
  10. 07.5 - 09 3rd Gen 6.7L Powertrain
    Only vehicle at the moment and single dad, would greatly appreciate any help from ya guys... Truck: 2007.5 dodge ram 2500 4x4 cummins 6.7L (was an auto, converted to G56? 6spd manual) Problem: Truck wouldnt start once and pushed the clutch in a little harder and it started, so, next time, few...
  11. 3rd Gen. Powertrain
    Hey all. I have owned my truck for about 30k miles. I am going to start with my clutch. I have no maintenance history before 178k miles. Judging from some aspects I have repaired, this baby was run hard and put up wet. But back to the topic. I have the following: Fleece Cheetah ATS...
  12. 3rd Gen. Powertrain
    Hi all, just reaching out to a forum to see if anybody’s got a smarter brain or has seen an issue that’s been plaguing my truck the last few months. Developed a knock that seems to run bad between 1400-1800 rpm regardless of gear, on an 04.5 with an nv5600 at 190000kms, automatically assumed...
  13. 94-98 Powertrain
    Does weight effect how much torque these clutches can handle. I found one rated at 1400 torque but I imagine that's at 60k lbs. In a 8000lb pickup would that clutch be able to handle more torque like between 1800-2000 lbs
  14. 07.5 - 09 3rd Gen 6.7L Non-Powertrain
    I bought a pre filled mastercylinder but did not come with bracket to mount through fire wall does anyone know where i can find the peice that smaps to it thats all i like.
  15. 98.5-02 Powertrain
    2001 Ram 2500 mildy built 5.9. NV5600 Transmission. Randomly started banging a fast high pitch knock at idle and increased with RPM. Inspected multiple areas. Thought it was even injectors. Threw alot of $$ on a set. Didnt cure. Separated Engine and transmission to find 1 of 2 rivets missing on...
  16. 3rd Gen. Non-Powertrain
    I want to flush the brakes and clutch cylinder with new brake fluid. I’m out by myself and think I heard someone talk about a brake pressure thing you can hook up the the reservoir. Pump that thing up and you can just go to the wheels and bleed the line. This right? And can I do the same...
  17. 98.5-02 Powertrain
    Hi all, I picked up a 7 speed Eaton w/OD TX-8607B. It’s going in a 2002 3500 24v 4x4 auto. I have most things sorted as far as a bellhousing, flywheel and clutch. Then I’m getting a hand from a local driveline shop for the T-case and shafts. The only thing now would be the clutch linkage and...
  18. 07.5 - 09 3rd Gen 6.7L Powertrain
    I know there is a lot of these posts, and I think I've read them all, but still not 100% sure so I need some help and insight guys. Swapping out a 68RFE to a fresh rebuilt NV5600. Using what I was told was an adapter plate out of a 05 NV5600 equipped truck. But now I'm having my doubts. I'm...
1-18 of 19 Results
Top