Search Results for ‘brakes’

Does anybody have any part numbers or brands for good steel braided brake lines for the 1st gen dodge rams? It’s has the 4500 axle up front. I need quality brake lines none of the cheap Chinese junk, as it never fits well or they won’t hold up to abuse that they need to hold up to. I prefer...

Before I place land mines downhill under each of my tires and set my truck in neutral I figured I’d reach out for feedback. Seems as if no matter what I do, be it OEM and upgrades, all lubed components, I still get the dying brake squeal! It’s a 17’ Mega Cab, 6” lift, 20” wheels, 37x13.5r20...

2003 Dodge Ram 2500 5.9 4x4 Does anyone know the flare nut sizes for the brake lines that go from the master cylinder to the abs box.

I inherited a beat up 01 3500 DRW about a year ago with a ton of problems. One problem I haven't been able to cure is the front brakes "groaning" or maybe rattling when first applied. I am back in the area to replace the hubs and am trying to cure the groan while I'm here. I got new brake...

About 3 weeks ago now I got new wheels/tires and was checking clearance on them. As I was turning the wheel I lost my power steering. Went for a drive also noticed I had lost brakes as well. Tried bleeding the pump and that didn’t get me anywhere. So far I purchased and installed new power...

I can feel the brake pedal move up and down and steering wheel wobbles left and right when braking hard, less when braking lightly. I saw a post this was a rear U joint and brake rotors and calipers all new. tires new, please help.

Yesterday I picked up my truck after having the AC fixed. They had to remove the entire dashboard to change out the recirculation door and the blend door motor. They also replaced the right rear wheel speed sensor. I was getting ABS, traction control, & 4x4 warning lights, which was the speed...

I just changed my front brake pads on my 2016 ram 2500 6.7 Cummins. I removed the master cylinder cap and used a C-clamp to compress the caliper pistons, so that the caliper would be easier to remove. I know a lot of folks recommend using the bleeder screws instead of pushing fluid backwards...

Your brakes are the single most important safety feature of your car, so if it's time to replace your brake pads or you just want an upgrade, we are here to help. AutoGuide has teamed up with NRS to offer up a free set of two NRS galvanized brake pads. To participate, please click here. The...

Drove for 5 minutes like a dink with the ebrake on. Got home and she was smokin pretty good. Been a couple days and the drum is still smoking and getting hot with the ebrake disengaged. Thinking maybe the ebrake got stuck? Hoping to not have to tear it all apart. Truck doesn’t pull to one side...

06 cummins mega, Ceramic Brakes and rotors have 3k miles on them and have squeaked ever since new. Comes and goes, but the squeek has to GO! It almost sounds like I can hear a slight squeal if Im passing a mountain wall, it echos back through the window barely. Ideas? Do the ceramic brakes...

recently I did a lot of brake work on the truck. 6 months ago, I changed everything on front axle. new flex hoses, calipers, rotors and pads. I also had to run a couple new brake lines as well from the abs module as they were rusted out. so the front has completely new brakes. after that I bled...

I recently purchased a 97 12 valve Cummins. When I hit the brakes in the slightest bit the truck starts to bog down and the engine pulses, and when I am stopped and press the brakes down a little more for a hill the truck stalls out. The truck also stalls when I go from stopped to about 1/4-1/2...

Im going to be replacing my brakes next week and wanted to do my front axle U-joints at the same time Should I go with Spicer or Yukon parts? What is the part number for the correct ones?

The rear brakes on my 09 3500 don't seem to be working very much. The truck stops ok, unless I'm on gravel or wet roads and then it will slide the front wheels. I pull a 36 ft gooseneck with it daily and again, it stopped ok on dry pavement. I have had the front tires chirp a little in a hard...

I want to keep my discs! But there is different mounting brackets welded to the axle. There's $500 kits online to do the conversion but that's if you don't have anything and I literally just need an adapter bracket... and maybe some new pads and shoes for the e break. I'm hoping the break lines...

I have a 2001 5.9 and the RED BRAKE light won’t turn off. Bought the truck and everything went fine then all of the sudden one day it stayed on. I have the nv4500 manual so I use the foot E-Brake as well as putting it in gear to keep it from rolling. ONLY THE RED BRAKE LIGHT IS ON. ABS light is...

Im having a problem with my front brakes dragging on my 12 valve with vacuum boost. I've replaced the front calipers and the booster and the pedal and pivot shaft also bled the entire system. The pedal is intermittently returning, it will drive for a bit and then the brakes heat up and drag...

2001, 3500 I’m desperate need of help. Iv been chasing a problem for a long time now. Vacuum pump went out one day so I replaced it, then replaced the power steering pump, then the brake booster, now the master. I’m on my 4th brake booster and still nothing. When I put a new booster on it, I...

I want to flush the brakes and clutch cylinder with new brake fluid. I’m out by myself and think I heard someone talk about a brake pressure thing you can hook up the the reservoir. Pump that thing up and you can just go to the wheels and bleed the line. This right? And can I do the same...