Cummins Diesel Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 21 Results
  1. 03 - 07 General Discussion
    I am looking to buy my first Cummins truck and have found a 2005 Laramie with the specs listed below. The seller says the truck has been well taken care of, but is asking for $26k which is nearly double the KBB value. I haven't found any trucks (with similar specs) being sold for this much, so...
  2. 03-07 Performance Parts Discussion
    So here’s my dilemma. I bought an 03 2500 from my best friend, and he got it from a good friend of his, said friend had the 48re built with billet bands, billet clutches, billet triple disc converter (but no input shaft or valve body…) installed fass fuel system, new head, arp head studs, and...
  3. New Member Introductions
    Hello everyone! I’ve got a 1997 2500 4x4 Turbo diesel Cummins with just over 184,000 miles. Extended cab with a long bed. We call her the Saturday Night Special 😎 Over the last few months I’ve noticed she’s running a little rough. Fuel mileage is not what it used to be for sure. She will blow...
  4. 03-07 Performance Parts Discussion
    The truck: 2005 5.9l, Manual 6spd, 100gph lift pump, Stock Cp3, 60hp injectors (BBI), Smarty S06 Revo#3 The goal - daily drive and occasional long heavy tow (20k) - add a turbo to the stock HE351 for an ultra fast spooling compound arrangement - don’t care about hp numbers beyond 600 (stock Cp3...
  5. 03-07 Powertrain
    Hey I am going to install new rocker arms part#4995602. Do I need to soak them in oil before I install them?
  6. 03 - 07 General Discussion
    Greetings all, I have a Dodge 3500 Single axel quad cab 5.9L with only 24,000 miles on it. I was t-boned between the drivers and rear passenger door. It was totaled. I’ve had a number of people people tell me different ways to fix it, one being a cab swap, the other being replacing the damaged...
  7. 89-93 Non-Powertrain
    Currently in the process of building and restoring a 5.9l 93’ 12v Cummins, bought it almost a year ago for a price I couldn’t say no to a 2WD LSD and got the transmission, engine, injectors, mechanical pump, replaced or fixed, readjusted valves. All there is to do is cosmetic upgrades and the...
  8. General Common Conversion FAQ & Tech
    I really need some help locating someone who is capable of a custom transmission job. I have a 2003 ram 2500 quad cab lond box. I am trying to get Ford's new 10R140 swapped into the truck. I have not been able to find much information on doing this. Any help is greatly appreciated.
  9. 2003 & Early 2004 Only Discussion
    All, I have a cold start problem with my 2003 dodge 2500 5.9l. I have done quite a bit of research and diagnosing after reading this forum so I need some help troubleshooting this lemon I bought. Will start after plugging in the block heater for about 1 hour. No codes or white/black smoke. Runs...
  10. 03-07 Performance Parts Discussion
    New here and somewhat new to the cummins fam, I just bought a 06 3rd gen 2500 5.9 24v (obviously), its got 190000 on it and i believe its stock other than a 5 inch turbo back exhaust, would it be safe to put a programmer on it? if so how much power could i add with stock internals. its a 6 speed...
  11. 03-07 Performance Parts Discussion
    I recently bought a 2006 5.9 3500 and I just started having this problem with it. It just started struggling to start(2-3 seconds it cranks, sometimes longer, before firing) but after it starts there's no problems with it. Also while set on cruise it will randomly start sputtering (like its...
  12. 03-07 Powertrain
    I have a 2006 Dodge Ram 3500 5.9L I have white smoke and idles rough and once I put it on drive and start driving in runs good but smokes less. i do half blow by as well. mom get codes p1757 Governor Low - pressure malfunction and p0606 internal ECM processor. What do I do?
1-20 of 21 Results
Top