Search Results for ‘2nd gen’

Hello, I bought a 97 cummins 3500 extended cab long bed 5 speed manual 4x4 a couple years back and been trying to get it to a point where it is safe to drive. The cab is not in good shape as well as cab mounts are almost non existent but the frame is in good shape. I’ve had opinions about the...

I recently put a rust free body from an 01 onto my 02. Both vin numbers from both trucks are on the cab itself, not the dashboard. Now I’m stuck with the wrong vin number for my truck since I couldn’t just swap dashes. Does anybody know what I can do to have the right vin number?

I'm thinking about buying a bd valve body and a suncoast cat 1 trans rebuild kit. Does anyone have experience with these? Would the be an issue mating these together? Will there be an issue with the 4.4 band lever and the valve body? Is this a wise purchase? Suncoast Category 1 450 HP 47RE...

Hey y'all Cummins lovers, I found a 2nd gen camper in good condition. Has anyone tried it? I checked all the forums but to no avail. The camper shell is 8ft long.

Last week my 99 QCLB started REALLY hesitating to move forward. I was able to limp home, but the RPMs were way above what they should've been for 12mph 2 days before this happened I noticed 2nd and maybe 3rd gear starts, launch stutters, and lockup stutters. The lockup stutters only happened in...

My number 6 piston on my 97 crumbled, would have to pull the block to bore the cylinder. I have a buddy with a 93 12v and a 01 24v Would rather just drop a working motor in and avoid rebuilding my 97 question is what would be the easier swap, newer or older? would like to keep my p-pump if i can

1999 dodge ram 2500. The truck starts to act like it's starving for fuel at 2500 rpms and doesn't climb hills like it used to (dropping into lower gears when before it would climb in overdrive). Air dog pump is delivering enough fuel (fuel pressure gauge) truck is tuned with an edge comp box and...

Hello all! I am installing a Thuren trac bar on my 2002. following the instructions, I used a grinder to allow for fitment on multiple places. However, the bottom bolt that holds the mounting bracket to the frame is off over 1/2 inch. Instructions state if the hole is off 1/8 inch or less to...

I have a 01 4x4 frame, and the trailing Arms (A-arms) are shot because the truck was wrecked. - $1200 OBO just trying to get rid of. passenger side full-size door - $125 OBO Passenger side fender - $75 OBO short Bed - $300 OBO Cab ( is dented by where pedals go because of a wreck) - $350...

My truck was driving fine tonight I had forward gears until I parked and had to readjust. Went back to drive and the engine doesn’t even get put under load in any forward gears. Gears seemed to be offset from their usual engaging points. Shut truck off and it wouldn’t start in park, moved it to...

2001 2500 24v 4x4 6sp Long Bed Quad Cab Laramie 70k miles Was driving last week and the truck just died, before this I did notice fuel pressure seemed to be low 5-10 at idle and near 0 under load. I got the truck back to the house, installed a FASS Titanium Signature Series 165GPH. Primed...

Well hey yall, I'm new to the forum world so please bear with me. I recently bought 1994 dually 2wd with an NV4500, the rear has been converted to what i believe is a dana 70 from 2500. I was wondering if theres a way to get the front hub to fit on the 3500 spindles so I don't have the dually...

Let’s set the stage, about a month ago I purchased a 1997 2500, 12 valve p pump with 200k and a new injection pump, guy I got it from said it had 50hp injectors( I’m new to diesels so forgive my possible arrogance and lack of good terminology) anyway, truck had a horrific tappet cover leak, shop...

Hello all, my rear speed sensors wire harness side has a missing plug. The sensor still has a plug. How do i determine which wire is for what side? I tried testing for positive and negative but i get nothing. Any ideas? Thanks in advance

So i recently acquired an HE300VG turbo with plans of swapping it into my 2nd gen 24v. I read old threads, did a lot of research on steed’s BANSHEE II controller (first of which i wanted to pick up) but it seems he sort of disappeared. Looked into the lil black box, but they wont manufacture...

Recently did a cab swap on my 98. Kept all 98 harnesses. The problem I’ve run into is that my blower stays running with ignition off/ key removed. The blower will not operate when key is in accessory or run position. I have replaced the ignition switch, resistor, tried a different head unit for...

Hey guys! I didn’t realize there was a detail section here so I wanted to post up my rig! I bought it a year ago and transformed it into the perfect work truck! I have on board water and electricity! I’ll be more than happy to explain the setup to anyone interested! . The truck build is on...

Hey everyone! I’ve finally decided to make an account and post up my build, it’s been almost a year and it’s a completely different truck! I bought the truck in Tampa Fl and immediately drove it across the state to Daytona Beach and it made the trip perfectly! She had a few issues including 2...

Hey everyone, I’ve been on these forums for a while now but finally decided to post my build! When I bought the truck it had sat in a field since 2016 and before that it was a ranch truck used to tow horse trailers. It had 203k miles on it and made the journey from Tampa to Daytona with no...

Hey y'all. I've got an 2001 24v. My drivers window likes to go down but then it will only go up a tiny bit at a time. I have to let is rest for a bit before it will go up again, but only a short bit each time. Sometimes it takes an hour or more just to put my window up. Passenger side works just...