Search Results for ‘24v cummins’

Bought a used vp44 with 50,000 kms on it, the truck it was on before still started and ran, put it on mine, no start, made sure key is in the timing gear keyway, no DTCs, everything hooked up as it should, but still won't start, only thing I haven't done is check for fuel pressure but I got a...

I'm thinking about buying a bd valve body and a suncoast cat 1 trans rebuild kit. Does anyone have experience with these? Would the be an issue mating these together? Will there be an issue with the 4.4 band lever and the valve body? Is this a wise purchase? Suncoast Category 1 450 HP 47RE...

I recently changed my clutch, upgraded from a single disc to a dual disc. The truck ran fine when I pulled it into the shop to change the clutch and now when I start it, it’s goes straight to 2650rpm and idles there. I still have throttle response and the quadzilla tuner is responding. I’m at a...

I have a 2006 2500 with the 5.9 24v HO 259,195 miles. And at any random time, it will full throttle and will bounce off the Rev limiter, but will shut off with the key. There is no repeatable way to make this happen, and it never throws an Engine light. It will do it at any speed, sometimes it...

Hey everyone I need help just replaced my injection pump after getting all the codes and went to go cut it off and turn it back on and code p0252 popped up and now it won’t start my friends say it could be the injection pump again but it was just put in like a week ago and has barely done any...

well today when I was pulling out of the gas station after filling up, I had the truck backfire on me and I didn't even know diesel could do that. anyways I looked at some older threads on other forum pages and some people said that the turbo was barking but that doesn't sound right. is my...

well today when I was pulling out of the gas station after filling up, I had the truck backfire on me and I didn't even know diesel could do that. anyways I looked at some older threads on other forum pages and some people said that the turbo was barking but that doesn't sound right. is my...

So boys fml clutch is ither smoked or soaked in oil and mail seal is dripping pretty good with any oil pressure. truck won move even in 4 low, wound out, I m wondering because of the fact I that I am going to be doing this solo would it be easier to pull the motor or push the 400lbs dry weight...

I have a 2003 24v common rail engine for sale, not a 53 block, has 106k on the odometer, comes with harness, guages, and 2006 ecm. I got it for a project but went with a 12v instead. 6k obo thanks

So I’m getting a p1765,p0753, and p1693 I’m not concerned about the last 2 for now but I need some test methods for that 1765, truck also does not charge alternator is good Checked trans relay No power to trans fuse but fuse isn’t blown

Hey everyone I'm having an oil pressure issue. yay.... anyways it has around 50psi on start up but when I let it sit and run for a good couple of minutes it drops down to around 30psi then it gets lower and lower, Etc. Etc. There is T6 rotella in the motor now since I couldn't find the T4 I...

Hey everyone, new to the forum and was doing some searching. Have my first second gen 2002 24valve 47re. I ran into a lock up issue and did some research. Found my alternator to be producing 0.07-0.08vac at idle from positive lead on alternator to alternator case . Unplugged alternator and road...

Hello, I have a 98 or 98.5 24v Cummins. I was just moving my truck to change the front and rear differential and as I was pulling out to head to my garage it wanted to die as I shifted from reverse to drive and as I shifted back to reverse. From all the discussion on here I see it might be a...

I'm not entirely sure if anyone else has encountered this issue but I am having a problem getting this part off of the mainshaft of my NV4500, anyone have any ideas of what this is or how I would get it off or if it even comes off?

Hey guys. So I was getting the p0336 code a little less than a month ago for crankshaft position sensor. Replaced the sensor and it fixed the problem. Fast forward to this Monday and I have been getting the same code again. I can clear the code but it just comes back either later that day or the...

I have a 1999 dodge 2500 2wd automatic that has 95k miles. The truck will start up just fine and crank just fine and idle just fine but won’t go over 10 mph or rev over 1400 rpm. I’ve been looking for a solid week for help or someone with the same issue that actually has a resolution to the...

just installed new valve spring, headgasket , pushrods, head studs, and rocker arm bolts. I cracked the injector lines to the crossover tubes and have fuel coming out of them, I have 17psi so im not sure why I'm having a crank/no start. the injectors are all brand new as well. does this have...

Just put a set of DFI SAC 7x0.013 injectors in the truck, would anybody be able to tell me the "hp" rating on these? i've looked at other threads on here and haven't really found a solid answer.

My 01 24v HO blew a head gasket and I’m wondering if there are any differences between the HO head gasket and the non HO. Planning on using the gasket set from Cummins part number 4090035, just making sure that will work for my truck.