Dodge Cummins Diesel Forum - Reply to Topic
98.5-02 Powertrain Discussion of components that are directly involved in the power production and all that is needed to get and keep the truck moving . Engine , Transmission Ect..NO ADVERTISING .

Thread: Truck cranking for 15-30 seconds before starting Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Dodge Cummins Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
10-15-2019 02:50 AM
bigfish95971 Just for fun, also have batteries load tested separately and disconnected. Unnoticeable only slightly slow cranking can act similar when a battery is going bad. If on is bad replace both.
10-14-2019 04:09 PM
hjablonski14 thanks will do
10-14-2019 04:13 AM
bigfish95971 It will start and run without even having grid heaters or relays, so not that. Your idle fuel pressure reading is probably off because it should not be more at highway than idle speed. So the 21 is likely more accurate and it is your problem. It shuts off a valve in the VP. Search threads here for no start high fuel pressure or similar for details.
10-14-2019 01:21 AM
hjablonski14 just did the hill test and it didn't make a difference, wait to start light comes on every time. It is throwing a glow plug circuit#2 code could that be it? it cant be the vp44 bc it has less than 5k miles on it since she went... when my fass and vp44 went I used the wiring harness that was already installed when I hooked up my fass and it did it a few times with the old pump... could the wiring harness be the issue?
10-13-2019 07:21 PM
bigfish95971 Outer module seal would not be the issue. But line couple seals could or damaged module.
Air leaks on fittings or return line fittings could be(hill test). Pressure too high is more likely if it is only when it is warmed up.., Batteries starting to go can be similar, but again it would be both hot and cold, or worse when cold.
Does Wait to Start light com on immediately with the key to ON. If not your ECM is bad and needs replacement and is the cause of delayed starting and grid heater code. It is not booting up for stasrt correctly, Used, or rebuilt and programmed replacemnt only, no do it your self fix.
10-13-2019 05:25 PM
hjablonski14 ALSO forgot to mention I have a super bad fuel leak on my tank seal. Could air be getting into the tank somehow causing it to crank so hard?
10-13-2019 03:01 PM
hjablonski14 is there a way to dumb it down?
10-13-2019 09:15 AM
ironpony idle pressure is too high to start, common problem, the VP likes less pressure on start up.
10-13-2019 12:39 AM
hjablonski14 Thanks man i'll try it tomorrow
10-12-2019 11:43 PM
bwdt Do the hill test. park the truck on a hill with the nose facing down, if the truck starts right up, you have an air leak on the return lines. if the truck is still hard to start, you may have a VP problem.
10-12-2019 11:34 PM
hjablonski14
Truck cranking for 15-30 seconds before starting

Hey guys I have a 98.5 24v, it has been running great recently, just replaced VP44 and fass and I have 15lbs of fuel pressure at idle and 21 at highway speeds. When I try to start the truck after I've been driving it for a while it cranks for 15-30 seconds before it fires up. I can hear the fass pumping but it still wont start. Truck has 286k on stock injectors so maybe thats the issue?? Any suggestions greatly appreciated.

ALSO truck is throwing a code for glow plug circuit #2 so that could also be the culprit. Thanks!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome