Dodge Cummins Diesel Forum - Reply to Topic
3rd Gen. Powertrain Discussion of components that are directly involved in the power production and all that is needed to get and keep the truck moving . Engine , Transmission Ect...NO ADVERTISING

Thread: Trans Temp Management Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Dodge Cummins Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
06-21-2019 02:16 AM
massmayhem The transducer also does have a temperature offset and scalar programmed into the ecm. Getting the transmission tuned to get into 3rd locked sooner, extending the 3-4 shift and stay held in lockup when off the throttle makes a big difference as well and eliminates the need of cycling between normal mode and tow/haul mode.
06-18-2019 10:05 PM
Galawcum Ok thanks a lot it sheds light on my tempature.
06-18-2019 09:11 PM
Eric-07 The pan is a good place to monitor as it will let the sensor be submerged in the fluid and give you a good representation of what’s going on.
Some guys put a sensor in the hot line which will show high temps because it’s right out of the converter and before any of the coolers. Some might put it in the return line which should show a nice cool temp being after the coolers but before it goes back into the trans. In the pan IMO kind of tells “the whole story” if you will.
06-18-2019 08:58 PM
Galawcum Gotcha! And if I was to install a second more accurate temp guage the pan is where I would put it correct?
06-18-2019 08:49 PM
Eric-07 I am saying it reads higher.
Due to location of the transducer it becomes heat soaked and what your seeing is more the temp of internal metal parts more so then your fluid temp.
Like I said before when I had a cts it would read up to 40* higher on really hot days then my analog gauge with the sensor in the pan submerged in fluid.
IMO the temps mentioned here are of no concern due to what I have experienced.
If you want to drive around in tow/haul go for it. It won’t hurt a thing. If not then don’t again I doubt it’ll hurt anything.
06-18-2019 07:58 PM
Galawcum So are you saying its actually showing higher than it is and I need to be in tow mode when sitting in slow traffic?
06-18-2019 07:41 PM
Eric-07 I would think the smarty gets its info from the same place (transducer) as the cts.
06-18-2019 05:22 PM
Galawcum Would the tranny temp read the same for a smarty that is pulling directly from ecm? I am having a similar issue with mine when sitting in traffic mine has seen low 200 after sitting in traffic 10minutes or even a drive through.
06-18-2019 07:52 AM
Woodyjiw I agree with Eric-07, I have an Edge as well and freaked out after I installed it because the trans temp was reading high, or so I thought. I installed an actual sensor in the pan and saw the temps over 30 cooler than the ECM reading from the Edge.

Nothing to work about...

Sent from my Pixel 2 using Tapatalk
06-18-2019 12:29 AM
Eric-07 If your seeing those temps from the edge alone and not an actual sensor you have zero issues to worry about. The edge gets its data from the transducer which is internal of the trans. An actual sensor in the pan reading those temps is really nothing to worry about either. (Sensor in the actual hot line will read higher then what your seeing now.)
When I had a cts it would read ~40* higher then my actual pan temp.
Get a real sensor in it somewhere before you worry about what you’re seeing.
06-17-2019 11:10 PM
05PowerHouse
Quote:
Originally Posted by kkosa812 View Post
Thanks for the info. I can turn it on on the fly or should I be stopped? And just switch it off when getting the highway? Ill try it tomorrow on my way to work.
Get in the habbit of tuning tow/haul mode on everytime you start your truck. Yes, once you enter a highway just click it off, when you exit click it back on. DO NOT click it on if you are above 60mph because this will cause your transmission to downshift.
06-17-2019 08:51 PM
kkosa812 Thanks for the info. I can turn it on on the fly or should I be stopped? And just switch it off when getting the highway? I’ll try it tomorrow on my way to work.
This thread has more than 12 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome