Dodge Cummins Diesel Forum - Reply to Topic
94-98 Powertrain Discussion of components that are directly involved in the power production and all that is needed to get and keep the truck moving . Engine , Transmission Ect...NO ADVERTISING

Thread: Oil pan gasket Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Dodge Cummins Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
06-06-2019 11:10 AM
spawn_x Used a cherry picker to lift the front of mine all the way to the top. Wasn't a big deal.

FYI new CUMMINS gasket was 4 piece - I didn't like that. When I started to tighten the bolts (in proper order), the gasket wanted to squeeze out. I would use either a one piece, OR a Mahle gasket. From my recent experience.
05-28-2019 08:06 PM
98whitelightnin I pretty much did it the way GAmes did and had no problems. I also left the pickup tube in place.
05-28-2019 07:50 PM
GAmes My transmission was still connected, obviously.
05-28-2019 02:39 PM
alanack6795
Quote:
Originally Posted by ekvhekvh View Post
That makes sense, thanks for clarification.
The engine leans forward without the trasmission, but it's still pretty balanced, you can actually lift it by hand.

I didnt need to remove the valve cover but it probably would have been easier.
05-28-2019 12:05 PM
ekvhekvh That makes sense, thanks for clarification.
05-28-2019 08:29 AM
GAmes He means you can put the jack under the crankshaft pulley. I prefer to lift it from the top with a hoist. The one time I did mine I disconnected the hoses into the inlet and out of the turbo. Removed #5 & 6 valve covers and covered the rockers to keep debris out, disconnected the exhaust downpipe and removed the fan. The engine will lift quite a ways up with those things disconnected. Loosen the bolts that are through the motor mounts enough for them to slide up the grooves. I also backed off the transmission mount bolts a bit. Once lifted I suggest you put blocks under the motor mounts in case the lifting device fails.
05-27-2019 11:40 PM
ekvhekvh “Just jack the motor up by the crank pulley.”

Not following that. You mean just rock it or let it slide up in the motor mounts?

When do you look at bearings? Mine has 225k
05-27-2019 02:23 PM
alanack6795 Take the rear adapter plate off, it will be easier. Just jack the motor up by the crank pulley.

Hardest part is dropping the pick up tube into the oil pan
05-27-2019 01:27 PM
ekvhekvh Went and looked again, not going to be fun.
05-27-2019 11:42 AM
blackDOHC You'll still need to lift the motor to lower the pan enough to drop the pickup tube inside. I replaced my oil pan when my trans was out and it still wasn't a fun day.
05-27-2019 06:51 AM
ekvhekvh I have transmission out and flex-plate off, will be installing a billet flex-plate.

Can I replace the pan gasket now without raising the motor? I probably should reseal the oil cooler and vacuum pump while there.

Any other suggestions while there?

I just did front cover and seals.

Thanks in advance

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome