|Topic Review (Newest First)|
|04-28-2019 01:49 PM|
Originally Posted by cerberusiam View Post
Exergy buys Bosch ones and enlarges them.
Unless I'm missing something
|04-28-2019 11:21 AM|
|04-26-2019 09:24 PM|
Originally Posted by Geowarrior View Post
It developed a slight knock. I had one go last year but it was the solenoid. This seems to be a dying injector. That's why I'm going to just replace them all.
Spoke with exergy. It's about $500 cheaper to buy stock Bosch ones and send them to exergy to enlarge and balance instead buying them from exergy.
|04-24-2019 01:43 AM|
Start small. A boost fooler will do most of what you want and not put you at any increased risk.
Next put in a shift kit to fix the shifting under load.
After that more air will do more than injectors-I used towing twins.
Now that you have more air add 90 injectors and put in a solid flex plate and consider built tranny.
Now you can consider race twins ungrade and need billet pieces in trans.
*Each step increases power. Each power step comes with more FUN and more WEAR. The more FUN, the more WEAR so BEWARE!!
Be safe, increase as pocket book allows, have FUN!!!
|04-24-2019 12:29 AM|
Quick question how did you determine “I had an injector go”. I’m concerned with 133,000 mi on 2006 as well.. I would appreciate your input.. thanks
|04-23-2019 05:02 PM|
|CumminUnGlued||I have a ii borgwarner s362 I would sell ya. It would go great with your build. PM me of interested.|
|04-23-2019 02:12 PM|
Originally Posted by TheKid760 View Post
I agree with a 362 with bbi .5s. Just because I think u need more injector. but as for putting down the 363, I disagree. All of that stuff sounds good on paper but my experience the 363 and 362 spool damn near identical. And the 363 has greater potential (future compounds or just peek hp) regardless of a possible slight efficiency loss.
|04-23-2019 10:57 AM|
Originally Posted by smelonas View Post
With only 0.5 bbi I think he should go 362.
In my opinion the 363sxe is a useless turbo. It flows less than 5 lb/min (some places site it as only 0.5 more, hard to read the edge of the map) over the 362, at a lower pr and efficiency.
Which means if you go with the 363 over the 362 then max hp potential gain is only 4-40 using the 8hp/lb rule of thumb. But due to the decrease in efficiency you gain about 44° outlet temperature at 40psig. And with a larger wheel it will inherently spool slower.
Sent from my iPhone using Tapatalk
|04-22-2019 11:49 PM|
Borg Warner 363sxe
Aftermarket manifold(either third gen or second gen style depending on depth of pockets)
MM3 with tunes by Gordon (dodge74 on here) or someone else on here
Single piece driveshaft
Added fuel filtration
Steering box brace
Bypass heat exchanger
Install dynamic transmission thermostat bypass in front cooler
That's a solid build right there. Should be good for many many carefree miles.
Sent from my SM-N950U using Tapatalk
|04-22-2019 09:31 PM|
|04-22-2019 08:46 PM|
I just recently went thru all this and came from the same turbo 4cyl background. Welcome to the forum.
|04-22-2019 08:14 PM|
Guys do run water meth systems in their pickups. I haven't really looked into them that much because i don't have a use for one. The horror stories (not that it's common) of them leaking causing hydro lock doesn't make me want one want more. But i guess you could always put a manual shut off valve in the line
The injectors are the heart of the engine. They can make it run great or destroy an engine pretty quick. Injectors are not something you should go cheap on.
30% overs will be fine with a stock turbo. Tuning will play a bigger role then a turbo when it comes to how clean it runs.
|This thread has more than 12 replies. Click here to review the whole thread.|