Dodge Cummins Diesel Forum - Reply to Topic
98.5-02 Performance Parts Discussion Discussion of Performance Parts For the 98-02 Trucks No Advertising ...NO ADVERTISING

Thread: Big single. Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Dodge Cummins Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
04-22-2019 09:12 PM
NCC74656 i have noticed on my compound setup that my coolant will rise in temp when i hammer but it comes back down with in 10 seconds or so of heavy loading. i also find i cant get full hard spool at low end unless i lock my TC. to that end i have my TC locking at about 12mph when i hit 80+% throttle and man does that change how the truck rockets. the tc lock alone adds a good 25psi of boost on top of what ever im at and then as the rpm's go back up the boost climes up and then gets another spike at the next shift point.

with out the TC locking the truck feels much like you are describing.
04-22-2019 08:30 PM
jkidd So you have upgraded valvesprings? Not a lot of power up in the higher rpm on a vp44 truck.

Nick was able to get QZ adrenaline to fuel to over 3700 rpm (data log showed continued fuel delivery)
04-20-2019 02:31 AM
Bivensz Also I've noticed, after a pull the engine temp goes up farther than normal operating temp. Usually stays right below half way mark and I'll do a pull and it'll go past the half mark and cool back down within a minute or so. Is that a sign of a head gasket leaking.? Doesnt leak any around the truck but wont stay 100% full of antifreeze. It's down an inch or 2 in the radiator.
04-20-2019 02:27 AM
Bivensz Got the turbo on, it runs pretty good but I'm still not happy with it. It comes on hard around 1900-2100. Sees 45-50 psi. It feels like it falls off on top end. Right before it shifts. It does clean the 250hp injectors up pretty decent. I'm thinking I may have a small boost leak somewhere.
04-11-2019 02:21 PM
jkidd Sounds good. Hope you will enjoy the extra air and potential for power.
04-08-2019 02:52 PM
Bivensz Havent been able to put it on yet. Truck will be back sometime this week from the transmission shop. As soon as I get it on I'll let you know.
04-08-2019 01:57 PM
jkidd How is the turbo working for you?
03-24-2019 03:14 AM
Bivensz Appreciate the info. Ended up ordering a 64.5/73/14 non gated. Going to do external gate later on if needed with nitrous. Dont have enough fuel to over spool the 64.5/73 without a gate right now
03-19-2019 12:35 PM
marco610 It's best to not run a t4 adapter, it's better to go with a t4 manifold if you're going that route. Imo t3 gated would still be a better choice, only time I would run t4 is if I was going with a s400.
03-19-2019 10:56 AM
jkidd It would spool close to 1900-2200 depending on elevation, tire size, axle ratio, torque converter (depends on how tight--- you want a loose converter.)

A gated 14cm should spool faster and flow more once the gates are open.

We sell a divided T4 Gated with HX40 outlet, its about the same price as the T3 gated.

Custom tuning from the Quadzilla Adrenaline will help too.
03-18-2019 10:55 PM
Bivensz Non gated housing as well
03-18-2019 10:55 PM
Big single.

How would a 64.5/73/.83 divided t4 sxe spool? 250hp injectors. So pump. Edge hot comp. Built auto. 2100 stall. Goal is 600-650 on fuel.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome