Southern Ms

[bkjeffrey]

Hey Pete Id like to catch up to ya sometime before the weekend because im putting on my big single and would like to see how you did yours. I finished sanding the stack today, tomorrow I will paint it and Id like to get it on maybe sunday.

__________________
04 QC/LWB 48RE 4x4: EJA, Arson CP3, BHAF, 4" TB stainless steel exhaust, 7" stack, Propane injection, Swanker intake manifold, GDP heater grid delete, BD 100 gal/hr pump, Big line kit, spin on fuel filter, Racor seperator, FS2500, mystery switch, 5 gallon on-board air system, Viair comp, Optima blue tops, 1875 Watt dvd stereo system, train horns. 6" lift w/35x12.50/20's

[6Cummins]

Originally Posted by bkjeffrey

Hey Pete Id like to catch up to ya sometime before the weekend because im putting on my big single and would like to see how you did yours. I finished sanding the stack today, tomorrow I will paint it and Id like to get it on maybe sunday.

Hope ya don't have a sliding rear glass like me! Mine vibrates so LOUD!!! Im about to have me a solid back window put in!! Alls ya do is get about 1ft of 4" flex pipe (2) band clamps and a 4" 90*. Depending on how long your stack is, you either lengthen your stack with some pipe to go below your bed or if your stacks long enough hook the 90 to your stack and then connect the flexpipe to the other side of your 90 and the flexp pipe slides over your 4" exhaust. You put band clamps on the flex pipe ends and I used a regular exhaust clamp on the 90 that meets the stack.. Very simple.. I used a stack clamp also on the stack to the bed rail

__________________
04 4dr 4wd Silver, Little bit of this and that..

---

Last edited by 6Cummins : 07-10-2008 at 03:35 PM.

[bkjeffrey]

Sweet, is your stack mounted directly above where the existing pipe was, like about a foot towards the center of the bed from the passenger side? Or is it snug in the corner of the bed. Im hoping I can put my stack in the passenger side corner of the bed so I dont have to move my tool box to the rear anymore. I can slide my toolbox to the left of the bed that leaves me with 8" on the right side of the bed to put my 7" stack.

No I dont have a sliding glass back window either, I always wished I did though.

__________________
04 QC/LWB 48RE 4x4: EJA, Arson CP3, BHAF, 4" TB stainless steel exhaust, 7" stack, Propane injection, Swanker intake manifold, GDP heater grid delete, BD 100 gal/hr pump, Big line kit, spin on fuel filter, Racor seperator, FS2500, mystery switch, 5 gallon on-board air system, Viair comp, Optima blue tops, 1875 Watt dvd stereo system, train horns. 6" lift w/35x12.50/20's

[2141pete]

Originally Posted by bkjeffrey

Hey Pete Id like to catch up to ya sometime before the weekend because im putting on my big single and would like to see how you did yours. I finished sanding the stack today, tomorrow I will paint it and Id like to get it on maybe sunday.

I was down at the shop today but I was on the bike. I have mine mounted bove the pipe since it was easier. I'm sure we can find a way to get it in there though. Dont laugh when you se tho hole in my bed though it is a long aggrivating story.

__________________

02 QC,4x4,TRE auto,AD150,BD twins, Mach5's,F1 springs,o-rings, studs,Quad ADR,smarty, Stewart warner gauges, a small shot of nitrous
12.71@104 #2 only 569/1080 as fast as it's gonna get till I start finding flashy stickers and free parts in the mail

[2141pete]

I have a slider and mine dont ratle a bit.

__________________

02 QC,4x4,TRE auto,AD150,BD twins, Mach5's,F1 springs,o-rings, studs,Quad ADR,smarty, Stewart warner gauges, a small shot of nitrous
12.71@104 #2 only 569/1080 as fast as it's gonna get till I start finding flashy stickers and free parts in the mail

[Kajun Kid 1971]

Thibodaux,La hear alot about guys around down here just haven,t found any yet

__________________
2003 Reg Cab white,ARE camper shell, minus muffler,silence ring gone, cool tube with AEM filter sp boost enforcer, 5"aero exhaust tip, BD pup,adjustable boost elbow dropped rear 3" ugly camper shell

[6Cummins]

Originally Posted by bkjeffrey

Sweet, is your stack mounted directly above where the existing pipe was, like about a foot towards the center of the bed from the passenger side? Or is it snug in the corner of the bed. Im hoping I can put my stack in the passenger side corner of the bed so I dont have to move my tool box to the rear anymore. I can slide my toolbox to the left of the bed that leaves me with 8" on the right side of the bed to put my 7" stack.

No I dont have a sliding glass back window either, I always wished I did though.

Mine sits right next to the right of the 3rd brake light. So ya right above the factory exhaust.

__________________
04 4dr 4wd Silver, Little bit of this and that..

[6Cummins]

Originally Posted by Kajun Kid 1971

Thibodaux,La hear alot about guys around down here just haven,t found any yet

around here or your way?

__________________
04 4dr 4wd Silver, Little bit of this and that..

[6Cummins]

Originally Posted by 2141pete

I have a slider and mine dont ratle a bit.

Must be nice! Gonna try to wedge some rubber behind it or something! SO AGGRAVTING

__________________
04 4dr 4wd Silver, Little bit of this and that..

[bkjeffrey]

Hey, how hot do you guys stacks get? I wanna paint my stack the same color as my truck, but I dont know if the stack will burn enamel paints off. I could do a high temp paint, but the color would be off a bit. I guess Caterpillar probably painted it black, because when I sanded it down today it sanded off pretty easy like an enamel. What do you guys think??

__________________
04 QC/LWB 48RE 4x4: EJA, Arson CP3, BHAF, 4" TB stainless steel exhaust, 7" stack, Propane injection, Swanker intake manifold, GDP heater grid delete, BD 100 gal/hr pump, Big line kit, spin on fuel filter, Racor seperator, FS2500, mystery switch, 5 gallon on-board air system, Viair comp, Optima blue tops, 1875 Watt dvd stereo system, train horns. 6" lift w/35x12.50/20's

[2141pete]

I would recommend a high temp, I melted a tarp to mine the other day lol.

__________________

02 QC,4x4,TRE auto,AD150,BD twins, Mach5's,F1 springs,o-rings, studs,Quad ADR,smarty, Stewart warner gauges, a small shot of nitrous
12.71@104 #2 only 569/1080 as fast as it's gonna get till I start finding flashy stickers and free parts in the mail

[2141pete]

I'll drive mine in the morning, I should be down at the ramp fighting wasp's again.

__________________

02 QC,4x4,TRE auto,AD150,BD twins, Mach5's,F1 springs,o-rings, studs,Quad ADR,smarty, Stewart warner gauges, a small shot of nitrous
12.71@104 #2 only 569/1080 as fast as it's gonna get till I start finding flashy stickers and free parts in the mail